U-Boot SPL 2020.07 (Oct 15 2020 - 00:10:34 +0200)
High speed PHY - Version: 2.0
MiniPCIe/mSATA card detection... MiniPCIe
Detected Device ID 6820
board SerDes lanes topology details:
 | Lane # | Speed |  Type       |
 --------------------------------
 |   0    |   5   | PCIe0       |
 |   1    |   5   | USB3 HOST0  |
 |   2    |   5   | PCIe1       |
 |   3    |   5   | USB3 HOST1  |
 |   4    |   5   | PCIe2       |
 |   5    |   0   | SGMII2      |
 --------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 0: remains Gen1
:** Link is Gen1, check the EP capability
PCIe, Idx 1: remains Gen1
PCIe, Idx 2: detected no link
High speed PHY - Ended Successfully
mv_ddr: mv_ddr-armada-18.09.2 
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
mv_ddr: completed successfully
Trying to boot from SPI


U-Boot 2020.07 (Oct 15 2020 - 00:10:34 +0200)

SoC:   MV88F6820-A0 at 1600 MHz
DRAM:  2 GiB (800 MHz, 32-bit, 2T, ECC not enabled)
Disabling MCU watchdog... disabled
WDT:   Started with servicing (60s timeout)
MMC:   mv_sdh: 0
Loading Environment from SPI Flash... SF: Detected s25fl164k with page size 256 Bytes, erase size 4 KiB, total 8 MiB
OK
Model: Turris Omnia
Turris Omnia:
  RAM size: 2048 MiB
  Serial Number: 0000000B00001D01
Regdomain set to **
PCI: Failed autoconfig bar 10
PCI: Failed autoconfig bar 14
PCI: Failed autoconfig bar 18
PCI: Failed autoconfig bar 1c
PCI: Failed autoconfig bar 10
PCI: Failed autoconfig bar 14
PCI: Failed autoconfig bar 18
PCI: Failed autoconfig bar 1c
Net:   eth0: ethernet@70000, eth1: ethernet@30000, eth2: ethernet@34000
Hit any key to stop autoboot:  0 
starting USB...
Bus usb@58000: USB EHCI 1.00
Bus usb3@f0000: MVEBU XHCI INIT controller @ 0xf10f4000
Register 2000120 NbrPorts 2
Starting the controller
USB XHCI 1.00
Bus usb3@f8000: MVEBU XHCI INIT controller @ 0xf10fc000
Register 2000120 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus usb@58000 for devices... 1 USB Device(s) found
scanning bus usb3@f0000 for devices... 1 USB Device(s) found
scanning bus usb3@f8000 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Device 0: Vendor: Generic  Rev: 8.07 Prod: Flash Disk      
            Type: Removable Hard Disk
            Capacity: 7800.0 MB = 7.6 GB (15974400 x 512)
... is now current device
Scanning usb 0:1...
Found U-Boot script /boot.scr
199 bytes read in 3 ms (64.5 KiB/s)
## Executing script at 01800000
269360 bytes read in 13 ms (19.8 MiB/s)
## Starting application at 0x01000000 ...
Consoles: U-Boot console  
Compatible U-Boot API signature found @0x7fbc6c18

FreeBSD/armv7 U-Boot loader, Revision 1.2
(Wed Oct 14 03:08:58 CEST 2020 root@mafl)

DRAM: 2048MB
MMC: no card present
Number of U-Boot devices: 1
U-Boot env: loaderdev not set, will probe all devices.
Found U-Boot device: disk
  Probing all <unknown> devices...
  Checking unit=0 slice=<auto> partition=<auto>... good.
Booting from disk0s2a:
Loading /boot/defaults/loader.conf
/boot/kernel/kernel text=0x8fa670 data=0xa2db0+0x55bd0 syms=[0x4+0x92230+0x4+0xeb74e]
/boot/entropy size=0x1000
/boot/kernel/carp.ko text=0x2b0c text=0x69f0 data=0x1088+0xfa4 syms=[0x4+0x1e40+0x4+0x134e]
/boot/kernel/if_bridge.ko text=0x28e0 text=0x71f0 data=0x1088+0xf7c syms=[0x4+0x20b0+0x4+0x1626]
loading required module 'bridgestp'
/boot/kernel/bridgestp.ko text=0xef4 text=0x4ad0 data=0x1088+0xf90 syms=[0x4+0xe90+0x4+0x862]
/boot/kernel/if_enc.ko text=0xe92 text=0x8b0 data=0x1088 syms=[0x4+0xb50+0x4+0xbc4]
/boot/kernel/if_gif.ko text=0x1b14 text=0x3ae0 data=0x1088+0xfa4 syms=[0x4+0x1a80+0x4+0xffa]
/boot/kernel/if_gre.ko text=0x2018 text=0x4d40 data=0x1088+0xf9c syms=[0x4+0x1c70+0x4+0x1056]
/boot/kernel/if_lagg.ko text=0x3800 text=0x8490 data=0x1088+0xf7c syms=[0x4+0x23e0+0x4+0x1558]
/boot/kernel/if_tap.ko text=0x1d0c text=0x2dd0 data=0x1088+0xfc0 syms=[0x4+0x16a0+0x4+0xc80]
/boot/kernel/if_tun.ko text=0x2549 text=0x3790 data=0x1088+0xfc8 syms=[0x4+0x1cd0+0x4+0x104a]
/boot/kernel/pf.ko text=0x70e4 text=0x31a10 data=0x3088+0x1074 syms=[0x4+0x5940+0x4+0x3612]
/boot/kernel/pflog.ko text=0xb24 text=0x830 data=0x1088 syms=[0x4+0x9d0+0x4+0x74d]
/boot/kernel/pfsync.ko text=0x2850 text=0x8340 data=0x1088+0xf7c syms=[0x4+0x1c90+0x4+0x12ab]

Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...               
/boot/dtb/armada-385-turris-omnia.dtb size=0x5dc5
Loaded DTB from file 'armada-385-turris-omnia.dtb'.
Kernel entry at 0x1400180...
Kernel args: (null)
SOC: Marvell 88F6820, TClock 250MHz, Frequency 1600MHz
  Instruction cache prefetch enabled, data cache prefetch disabled
---<<BOOT>>---
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 2013-2019 The HardenedBSD Project.
Copyright (c) 1992-2019 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.1-RELEASE-p10-HBSD #3  6e16e28f1(stable/20.7)-dirty: Thu Oct 15 15:15:40 CEST 2020
    root@mafl:/usr/obj/usr/src/arm.armv7/sys/SMP-OMNIA arm
FreeBSD clang version 8.0.1 (tags/RELEASE_801/final 366581) (based on LLVM 8.0.1)
HardenedBSD: initialize and check features (__HardenedBSD_version 1200059 __FreeBSD_version 1201000).
CPU: ARM Cortex-A9 r4p1 (ECO: 0x00000000)
CPU Features: 
  Multiprocessing, Thumb2, Security, VMSAv7, Coherent Walk
Optional instructions: 
  UMULL, SMULL, SIMD(ext)
LoUU:2 LoC:2 LoUIS:2 
Cache level 1:
 32KB/32B 4-way data cache WB Read-Alloc Write-Alloc
 32KB/32B 4-way instruction cache Read-Alloc
real memory  = 2147479552 (2047 MB)
avail memory = 2089525248 (1992 MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
random: unblocking device.
wlan: mac acl policy registered
random: entropy device external interface
[ath_hal] loaded
000.000021 [4335] netmap_init               netmap: loaded module
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
simplebus1: <Flattened device tree simple bus> on simplebus0
l2cache0: <PL310 L2 cache controller> mem 0x8000-0x8fff on simplebus1
l2cache0: cannot allocate IRQ, not using interrupt
l2cache0: Part number: 0x3, release: 0x9
l2cache0: Warning: L2 Cache should not already be active; trying to de-activate and re-initialize...
l2cache0: L2 Cache enabled: 1024KB/32B 16 ways
gic0: <ARM Generic Interrupt Controller> mem 0xd000-0xdfff,0xc100-0xc1ff on simplebus1
gic0: pn 0x39, arch 0x1, rev 0x2, implementer 0x43b irqs 192
mpic0: <Marvell Integrated Interrupt Controller> mem 0x20a00-0x20ccf,0x21070-0x210c7 irq 17 on simplebus1
gpio0: <Marvell Integrated GPIO Controller> mem 0x18100-0x1813f,0x181c0-0x181c7 irq 9,10,11,12 on simplebus1
gpio0: 4 IRQs available
gpio0: Disable interrupts (offset = 0 + EDGE(0x18)
gpio0: Disable interrupts (offset = 0 + LEV(0x1C))
gpio0: Setup intr 0
gpio0: Setup intr 1
gpio0: Setup intr 2
gpio0: Setup intr 3
gpio0: Clear int status (offset = 0)
gpiobus0: <GPIO bus> on gpio0
gpio1: <Marvell Integrated GPIO Controller> mem 0x18140-0x1817f,0x181c8-0x181cf irq 13,14,15,16 on simplebus1
gpio1: 4 IRQs available
gpio1: Disable interrupts (offset = 0 + EDGE(0x18)
gpio1: Disable interrupts (offset = 0 + LEV(0x1C))
gpio1: Setup intr 0
gpio1: Setup intr 1
gpio1: Setup intr 2
gpio1: Setup intr 3
gpio1: Clear int status (offset = 0)
gpiobus1: <GPIO bus> on gpio1
mp_tmr0: <ARM MPCore Timers> mem 0xc200-0xc21f irq 3 on simplebus1
Timecounter "MPCore" frequency 800000000 Hz quality 800
mp_tmr1: <ARM MPCore Timers> mem 0xc600-0xc61f irq 4 on simplebus1
Event timer "MPCore" frequency 800000000 Hz quality 1000
twsi0: <Marvell Integrated I2C Bus Controller> mem 0x11000-0x1101f irq 5 on simplebus1
iicbus0: <OFW I2C bus> on twsi0
iic0: <I2C generic I/O> on iicbus0
iicbus0: <unknown card> at addr 0xe0
uart0: <16550 or compatible> mem 0x12000-0x120ff irq 7 on simplebus1
uart0: console (-1,n,8,1)
uart1: <16550 or compatible> mem 0x12100-0x121ff irq 8 on simplebus1
gpioc0: <GPIO controller> on gpio0
gpioc1: <GPIO controller> on gpio1
wdt0: <Marvell Watchdog Timer> mem 0x20300-0x20333,0x20704-0x20707,0x18260-0x18263 on simplebus1
pmsu0: <Power Management Service Unit> mem 0x22000-0x22fff on simplebus1
mvneta0: <NETA controller> mem 0x70000-0x73fff irq 24 on simplebus1
mvneta0: version is 10
mvneta0: Ethernet address: d8:58:d7:00:22:79
mvneta1: <NETA controller> mem 0x30000-0x33fff irq 25 on simplebus1
mvneta1: version is 10
mvneta1: Ethernet address: d8:58:d7:00:22:77
mvneta2: <NETA controller> mem 0x34000-0x37fff irq 26 on simplebus1
mvneta2: version is 10
mvneta2: Ethernet address: d8:58:d7:00:22:78
miibus0: <MII bus> on mvneta2
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
ehci0: <Marvell Integrated USB 2.0 controller> mem 0x58000-0x584ff irq 27 on simplebus1
usbus0: EHCI version 1.0
usbus0 on ehci0
cesa0: <Marvell Cryptographic Engine and Security Accelerator> mem 0x90000-0x9ffff irq 28,29 on simplebus1
rtc0: <Marvell Integrated RTC> mem 0xa3800-0xa381f,0x184a0-0x184ab irq 30 on simplebus1
rtc0: registered as a time-of-day clock, resolution 1.000000s
ahci0: <Marvell AHCI Controller> mem 0xa8000-0xa9fff irq 31 on simplebus1
ahci0: AHCI v1.00 with 2 6Gbps ports, Port Multiplier supported with FBS
ahci0: quirks=0x200010<2CH,MRVL_SR_DEL>
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
armada_thermal0: <Armada380 Thermal Control> mem 0xe4078-0xe407b,0xe4070-0xe4077 on simplebus1
device_attach: armada_thermal0 attach returned 6
sdhci_fdt0: <ARMADA38X SDHCI controller> mem 0xd8000-0xd8fff,0xdc000-0xdc0ff,0x18454-0x18457 irq 34 on simplebus1
sdhci_fdt0: 1 slot(s) allocated
xhci0: <Marvell Integrated USB 3.0 controller> mem 0xf0000-0xf3fff,0xf4000-0xf7fff irq 35 on simplebus1
xhci0: 32 bytes context size, 32-bit DMA
usbus1 on xhci0
xhci1: <Marvell Integrated USB 3.0 controller> mem 0xf8000-0xfbfff,0xfc000-0xfffff irq 36 on simplebus1
xhci1: 32 bytes context size, 32-bit DMA
usbus2 on xhci1
cesa1: <Marvell Cryptographic Engine and Security Accelerator> mem 0x90000-0x9ffff irq 37,38 on simplebus1
pcib_ctrl0: <Marvell Integrated PCIe Bus Controller> on simplebus0
pcib0: <Marvell Integrated PCI/PCI-E Controller> on pcib_ctrl0
pci0: <PCI bus> on pcib0
ath0: <Atheros 9287> mem 0xf1800000-0xf180ffff at device 1.0 on pci0
ath0: [HT] enabling HT modes
ath0: [HT] enabling short-GI in 20MHz mode
ath0: [HT] 1 stream STBC receive enabled
ath0: [HT] 1 stream STBC transmit enabled
ath0: [HT] 2 RX streams; 2 TX streams
ath0: AR9287 mac 384.2 RF5133 phy 15.15
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x00c0
pcib1: <Marvell Integrated PCI/PCI-E Controller> on pcib_ctrl0
pci1: <PCI bus> on pcib1
pcib2: <Marvell Integrated PCI/PCI-E Controller> on pcib_ctrl0
pci2: <PCI bus> on pcib2
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpu1: <Open Firmware CPU> on cpulist0
cryptosoft0: <software crypto>
Timecounters tick every 1.000 msec
mvneta0: link state changed to UP
mvneta1: link state changed to UP
usbus0: 480Mbps High Speed USB v2.0
usbus1: 5.0Gbps Super Speed USB v3.0
usbus2: 5.0Gbps Super Speed USB v3.0
ugen0.1: <Marvell EHCI root HUB> at usbus0
uhub0: <Marvell EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Marvell XHCI root HUB> at usbus1
uhub1: <Marvell XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus1
ugen2.1: <Marvell XHCI root HUB> at usbus2
uhub2: <Marvell XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus2
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
mmc0: <MMC/SD bus> on sdhci_fdt0
mmcsd0: 8GB <MMCHC H8G4a� 10.1 SN 22A1AC31 MFG 04/2016 by 144 0x004a> (read-only) at mmc0 50.0MHz/8bit/65535-block
mmcsd0boot0: 4MB partition 1 (read-only) at mmcsd0
mmcsd0boot1: 4MB partition 2 (read-only) at mmcsd0
mmcsd0rpmb: 4MB partition 3 (read-only) at mmcsd0
uhub0: 1 port with 1 removable, self powered
ugen2.2: <Generic Mass Storage> at usbus2
umass0 on uhub2
umass0: <Generic Mass Storage, class 0/0, rev 2.00/1.00, addr 1> on usbus2
Release APs
Trying to mount root from ufs:/dev/ufs/OPNsense [rw]...
da0 at umass-sim0 bus 0 scbus2 target 0 lun 0
da0: <Generic Flash Disk 8.07> Removable Direct Access SPC-2 SCSI device
da0: Serial Number 34809E2F
da0: 40.000MB/s transfers
da0: 7800MB (15974400 512 byte sectors)
da0: quirks=0x2<NO_6_BYTE>
Mounting filesystems...
tunefs: soft updates remains unchanged as enabled
tunefs: file system reloaded
da0 recovering is not needed
da0s1 resized
growfs: requested size 2.0GB is not larger than the current filesystem size 2.0GB
camcontrol: ATA ATA_IDENTIFY via pass_16 failed
camcontrol: ATA ATAPI_IDENTIFY via pass_16 failed
** /dev/ufs/OPNsense
FILE SYSTEM CLEAN; SKIPPING CHECKS
clean, 196828 free (300 frags, 24566 blocks, 0.1% fragmentation)
/etc/rc.d/hostid: WARNING: hostid: unable to figure out a UUID from DMI data, generating a new one
Setting hostuuid: ba67001a-0f04-11eb-9da3-d858d7002279.
Setting hostid: 0x26b50523.
Press any key to start the configuration importer: .........
Bootstrapping config.xml...done.
Configuring crash dump device: /dev/null
.ELF ldconfig path: /lib /usr/lib /usr/local/lib /usr/local/lib/compat/pkg /usr/local/lib/compat/pkg /usr/local/lib/ipsec /usr/local/lib/perl5/5.32/mach/CORE
Soft Float compatibility ldconfig path:
done.

>>> Invoking early script 'update'
>>> Invoking early script 'configd'
Starting configd.
>>> Invoking early script 'templates'
Generating configuration: OK
>>> Invoking early script 'backup'
>>> Invoking backup script 'captiveportal'
>>> Invoking backup script 'dhcpleases'
>>> Invoking backup script 'duid'
>>> Invoking backup script 'netflow'
>>> Invoking backup script 'rrd'
>>> Invoking early script 'carp'
CARP event system: OK
Launching the init system...done.
Initializing...........done.
mvneta2: link state changed to DOWN
Starting device manager...devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
devmatch: Can't read linker hints file.
done.
Configuring login behaviour...done.

Default interfaces not found -- Running interface assignment option.

Press any key to start the manual interface assignment: 5
Valid interfaces are:
mvneta0          d8:58:d7:00:22:79 NETA controller
mvneta1          d8:58:d7:00:22:77 NETA controller
mvneta2          d8:58:d7:00:22:78 NETA controller
[ar5210] loaded
[ar5211] loaded
[ar5212] loaded
[ar5416] loaded
[ar9300] loaded
[ath_rate] loaded
[ath_dfs] loaded
[ath] loaded
ath0              Atheros 9287

You now have the opportunity to configure VLANs.  If you don't require VLANs
for initial connectivity, say no here and use the GUI to configure VLANs later.

Do you want to configure VLANs now? [y/N]: n

If you do not know the names of your interfaces, you may choose to use
auto-detection. In that case, disconnect all interfaces now before
hitting 'a' to initiate auto detection.

Enter the WAN interface name or 'a' for auto-detection: a

Connect the WAN interface now and make sure that the link is up.
Then press ENTER to continue.

No link-up detected.

Enter the WAN interface name or 'a' for auto-detection: 

Enter the LAN interface name or 'a' for auto-detection
NOTE: this enables full Firewalling/NAT mode.
(or nothing if finished): 

Enter the Optional interface 1 name or 'a' for auto-detection
(or nothing if finished): 

No interfaces will be assigned!

Do you want to proceed? [y/N]: y

Writing configuration...done.
Configuring loopback interface..lo0: link state changed to UP
.done.
Configuring kernel modules...done.
Setting up extended sysctls...done.
Setting timezone...done.
Writing firmware setting...done.
Writing trust files...done.
Setting hostname: OPNsense.localdomain
Generating /etc/hosts...done.
Configuring system logging...done.
Configuring loopback interface...done.
Creating wireless clone interfaces...done.
Creating IPsec VTI instances...done.
Generating /etc/resolv.conf...done.
Configuring firewall........done.
Starting PFLOG...done.
Starting web GUI...done.
Configuring CRON...done.
Setting up routes...done.
Generating /etc/hosts...done.
Starting Unbound DNS...done.
Setting up gateway monitors...done.
Configuring firewall........done.
Starting PFLOG...done.
Syncing OpenVPN settings...done.
Starting NTP service...deferred.
Starting Unbound DNS...done.
Generating RRD graphs...done.
Configuring system logging...done.
>>> Invoking start script 'newwanip'
>>> Invoking start script 'freebsd'
>>> Invoking start script 'syslog-ng'
Stopping syslog_ng.
Waiting for PIDS: 49284.
Starting syslog_ng.
>>> Invoking start script 'carp'
>>> Invoking start script 'cron'
Starting Cron: OK
>>> Invoking start script 'beep'
Root file system: /dev/ufs/OPNsense
Thu Oct 15 16:42:16 UTC 2020

*** OPNsense.localdomain: OPNsense 20.7.3_5 (armv7/OpenSSL) ***

        No network interfaces are assigned.